GeckoTek — 3D Printer Build Surfaces

Shop

One sheet. Every printer.

EZ-Stik HOT

★★★★★4.8 (612)

Heated beds & tough materials — ABS, PETG, Nylon, carbon-fiber. Locks the first layer hot, releases clean cool. Backed by our money-back guarantee.

$7

Printer-specific

Find the exact sheet for your printer.

Search 50+ popular printers for the right EZ-Stik and cut size — or enter your bed dimensions. GeckoTek fits every printer ever made.

Search your printer

Popular: Bambu A1· Ender 3 V3· Creality K1C· Prusa MK4S· Kobra 3 Don’t see yours? Enter bed size →

Resources

Everything you need to nail every print.

How to apply EZ-Stik

Measure, cut, and bubble-free application in under two minutes.

Read guide →

Temperature settings

Dialed-in bed & nozzle temps for PLA, ABS, PETG, Nylon & flexibles.

View chart →

Care & longevity

Keep a single sheet running up to 100 prints — cleaning & do’s/don’ts.

Read guide →

Printer

Recommended sheet

Size

Bambu Lab A1 / P1S

EZ-Stik HOT

256 × 256 mm · shop

Creality Ender 3 V3

EZ-Stik HOT

235 × 235 mm · shop

Creality K1 / K1C

EZ-Stik HOT

220 × 220 mm · shop

Prusa MK4S

EZ-Stik HOT

250 × 210 mm · shop

Anycubic Kobra 3

EZ-Stik HOT

250 × 250 mm · shop

Any large-format printer

EZ-Stik HOT

Custom / trim-to-fit · shop

Will it fit my printer?

Yes — EZ-Stik ships oversized and cuts to any bed with household scissors. If your bed is bigger than our largest sheet, use the finder above for the closest fit.

Does it work over a textured PEI plate?

EZ-Stik HOT lays over your existing plate and gives a smooth, consistent surface with strong adhesion for ABS/PETG/nylon — and a glassy bottom finish most stock plates can’t match.

How many prints does one sheet last?

A single sheet gives you up to 100 prints with good care. When adhesion finally fades, peel and apply a fresh sheet in minutes.

Which filaments does EZ-Stik HOT work with?

EZ-Stik HOT is built for heated beds and handles everything from PLA and PETG to tougher engineering materials like ABS, nylon, and carbon-fiber blends. Strong adhesion while hot, clean release once the bed cools.

Do you ship internationally?

We ship worldwide from the USA. US orders over $35 ship free.

First layer won’t stick

Clean the surface with IPA, re-level so the nozzle is a hair closer, and match the bed temp on our settings chart. A slightly slower first-layer speed helps too.

Parts stick too hard when cool

Let the bed cool fully — EZ-Stik releases as it drops below release temperature. If it’s still tight, a gentle flex of a flexible plate or a few extra minutes cooling pops it free.

Bubbles under the sheet

Peel back to the bubble, smooth outward from the center with a card, and re-lay. Small bubbles away from the print area won’t affect results.

Sheet lifting at the edges

Ensure the bed was clean and dry before applying. Trim any overhang past the heated zone; overhanging film can catch and lift.

See it work

Stick it once. Print up to 100 times.

Real EZ-Stik, real printer, real hands. Rock-solid adhesion while printing, then parts typically come up by hand once the bed cools.

The 3-step routine →

Three steps

Cut. Stick. Print.

No glue stick. No hairspray. No painter’s tape. No special tools.

01

Cut to your bed

Measure, then cut with household scissors. Fits every printer ever made.

02

Peel & stick, once

Self-adhesive backing. Smooth it flat, bubble-free, set for up to 100 prints.

03

Print & pop off

Rock-solid first layer hot. Cool it — parts release clean, every time.

The science

Grips when hot. Releases when cool.

The proprietary polymer coating changes tack with temperature — maximum grip at printing heat so the first layer never lifts, then it lets go as the bed cools so parts pop off without a scraper. Dialed-in settings for every filament come on the sheet.

HOT · printing → bonded, zero warpCOOL · done → clean release

EZ-STIK™

HOT

Bed

ABS100–110°C

PLA50–60°C

PETG70–80°C

Nylon30–50°C

Flexible50°C

Extruder

ABS230°C

PLA200°C

PETG230°C

Nylon230°C

Flexible230°C

Scientifically formulated for easy printing and removal · geckotek.co

vs. everything

Why makers keep coming back.

Surface

Prep each print

Lifespan

Smooth finish

GeckoTek EZ-Stik

None

Up to 100 prints

Best-in-class

Glue stick

Re-apply every print

Single use

Streaky

Painter’s tape

Replace per print

1–2 prints

Textured

Bare textured PEI

Occasional wash

Wears / chips

Grainy bottom

Get dialed-in settings + 10% off

Filament profiles, new-printer compatibility drops, and the occasional maker tip. No spam.